Wigo

Wigo (What Is Going On) is a lightweight pull/push monitoring tool written in Go.

Features

• Probes in any language — Write probes as binaries in the language of your choice
• Notifications — HTTP, email, and Apprise alerts when probe or host status changes
• Proxy mode — Monitor hosts behind NAT/gateways via PUSH mode
• Metrics — Send probe metrics to OpenTSDB

Screenshots

Main view

Group view

Host view

---

Monitoring modes: PULL and PUSH

Wigo can collect data from other Wigo instances in two ways.

PULL mode

The master (central Wigo) periodically fetches data from remote Wigos over HTTP/HTTPS.

• You configure a list of remote hosts in [RemoteWigos] (see Configuration).
• The master polls each remote at CheckInterval seconds by requesting GET /api (full JSON state).
• Remotes must expose the HTTP API (default port 4000). Use firewall rules, TLS, and optional HTTP Basic Auth to secure access.
• Use case: You can open the master’s network to outbound connections; remotes are just normal Wigo instances with the HTTP API enabled.

PUSH mode

Clients (e.g. hosts behind NAT) send their state to a central Wigo over a persistent TCP connection.

• You enable [PushServer] on the central Wigo and [PushClient] on each client.
• Clients connect to the server (default port 4001), authenticate with a signed UUID, then periodically push their state via RPC (binary gob over TCP).
• TLS is strongly recommended. The server uses a CA certificate to sign client UUIDs; clients use the server certificate to verify the server.
• Use case: Hosts that cannot be reached from the master (NAT, no public IP). They initiate the connection and push their probes and status.

You can combine both: a master can have some remotes via PULL (HTTP) and others via PUSH (TCP).

---

Status codes

Every probe returns a numeric Status. Wigo uses it for aggregation and notifications.

Code	Label	Meaning
100	OK	All good
101–199	INFO	Informational (e.g. minor notice)
200–299	WARN	Warning, attention needed
300–499	CRIT	Critical, should be fixed
500+	ERROR	Error or failure (e.g. probe timeout, exec failure)

• Host status is the maximum of its probe statuses (worst probe wins).
• A host that has not reported in time is marked DOWN (status 999).
• Notifications are sent when a probe’s status changes and crosses the threshold defined by MinLevelToSend (e.g. only WARN and above). You can also get notified when a host goes UP or DOWN.

---

Installation

Packages for Debian 12 (Bookworm) are available from the project repository:

apt-get install lsb-release
sudo mkdir -p /etc/apt/keyrings
wget -qO- http://deb.carsso.com/deb.carsso.com.key | gpg --dearmor | sudo tee /etc/apt/keyrings/deb.carsso.com.gpg > /dev/null
echo "deb [signed-by=/etc/apt/keyrings/deb.carsso.com.gpg] http://deb.carsso.com $(lsb_release -cs) main" | sudo tee /etc/apt/sources.list.d/deb.carsso.com.list
apt-get update
apt-get install wigo

Alternatively, you can build the packages from source (see Building from source) or download the latest release from the releases page.

Optional: Install the Wigo Monitoring browser extension for Chrome or Firefox.

---

Configuration

• Main config file: /etc/wigo/wigo.conf.
• Probes config: /etc/wigo/conf.d/.

The main config file is split into sections. Below is what each section does and the main options.

[Global]

Option	Description
Hostname	This machine’s hostname (default: system hostname).
Group	Logical group (e.g. webserver, loadbalancer) for the UI and OpenTSDB tags.
LogFile	Log path (e.g. /var/log/wigo.log).
ProbesDirectory	Where probe executables live (e.g. /usr/local/wigo/probes).
ProbesConfigDirectory	Directory for per-probe config (e.g. /etc/wigo/conf.d).
UuidFile	Path where the instance UUID is stored.
Database	SQLite DB to store data (logs, status, etc.) (e.g. /var/lib/wigo/wigo.db).
AliveTimeout	Seconds without update before a remote is considered DOWN (e.g. 60).
Debug	Enable debug logging.

[Http]

HTTP API (used by the web UI and by PULL mode).

Option	Description
Enabled	Turn the HTTP server on/off.
Address, Port	Listen address (e.g. 0.0.0.0, 4000).
SslEnabled	Use HTTPS.
SslCert, SslKey	Paths to the server certificate and private key.
Login, Password	Optional HTTP Basic Auth for the API.

[PushServer]

Central server for PUSH mode (clients connect here).

Option	Description
Enabled	Enable the push server.
Address, Port	Listen address (e.g. 0.0.0.0, 4001).
SslEnabled	Use TLS (recommended).
SslCert, SslKey	CA certificate and private key (used to sign client UUIDs).
AllowedClientsFile	File listing allowed client UUIDs (one per line).
AutoAcceptClients	If true, new clients are accepted without manual approval.

[PushClient]

Client side for PUSH mode (this instance pushes to a central Wigo).

Option	Description
Enabled	Enable the push client.
Address, Port	Push server host and port.
SslEnabled	Use TLS (recommended).
SslCert	Path to the server’s certificate (e.g. /var/lib/wigo/master.crt) so the client can verify the server.
UuidSig	Path where the server’s signature of this client’s UUID is stored.
PushInterval	Seconds between state pushes (e.g. 10).

[RemoteWigos]

List of remotes for PULL mode. The master polls these via HTTP.

Option	Description
CheckInterval	Seconds between polls per remote (e.g. 10). Do not set below about half of AliveTimeout.
SslEnabled	Use HTTPS when polling.
Login, Password	HTTP Basic Auth for remote APIs.
List	Simple list: ["host1", "host2:4000", ...]. Port optional (default: master’s HTTP port).

For per-host options (custom port, TLS, auth, depth), use the advanced form in the config file (see comments in etc/wigo.conf).

[OpenTSDB]

Optional: send probe metrics to OpenTSDB.

Option	Description
Enabled	Enable OpenTSDB output.
Address	OpenTSDB host(s).
MetricPrefix	Prefix for metric names (e.g. wigo).
Deduplication, BufferSize	Tuning for metric submission.

[Notifications]

Alerts when probe or host status changes.

Option	Description
MinLevelToSend	Minimum status to trigger a notification (e.g. 250 = WARN and above).
OnProbeChange	Notify on probe status change.
OnWigoChange	Notify when a host goes UP/DOWN.
HttpEnabled, HttpUrl	HTTP POST callback with notification payload.
EmailEnabled, EmailSmtpServer, EmailRecipients, …	SMTP email alerts.
AppriseEnabled, ApprisePath, AppriseUrls	Alerts via Apprise.

---

TLS

HTTPS API (PULL and web UI)

Use a server certificate and key so the HTTP API is served over HTTPS.

Generate a self-signed certificate (replace hostnames/IPs as needed):

/usr/local/wigo/bin/generate_cert -ca=false -duration=876000h0m0s -host "hostname,ip1,ip2" --rsa-bits=4096

Then set in [Http]: SslEnabled = true, and point SslCert / SslKey to the generated files.

You may want to order a certificate from a trusted CA like Let's Encrypt instead of using a self-signed certificate.

PUSH mode (server and clients)

The push server uses a CA certificate to sign client UUIDs. Clients use the server’s certificate to verify the server.

On the push server, generate a CA key pair:

/usr/local/wigo/bin/generate_cert -ca=true -duration=876000h0m0s -host "hostnames,ips,..." --rsa-bits=4096

Configure [PushServer] with these cert/key paths. Copy the certificate (not the key) to each client and set [PushClient].SslCert to that path. On first connect, the client can optionally fetch the server cert via RPC and then reconnect with verification enabled.

---

Probes

Probes live under ProbesDirectory (e.g. /usr/local/wigo/probes).

Subdirectory name is the check interval in seconds (60, 120, 300) (e.g. /usr/local/wigo/probes/60). They are executed automatically every time the interval is reached.

Probes in subdirectories are symlinks to the actual probe executable located in the examples subdirectory (e.g. /usr/local/wigo/probes/60/check_mdadm -> /usr/local/wigo/probes/examples/check_mdadm).

Probes config files are located in ProbesConfigDirectory (e.g. /etc/wigo/conf.d).

Writing a probe

A probe is an executable (any language) that prints a single JSON object to stdout. Required field: Status (integer, see Status codes). Optional: Message, Detail, Version, Metrics (for OpenTSDB).

Example output:

{
  "Status": 100,
  "Message": "0.38 0.26 0.24",
  "Detail": "",
  "Version": "0.11",
  "Metrics": [
    { "Value": 0.38, "Tags": { "load": "load5" } },
    { "Value": 0.26, "Tags": { "load": "load10" } },
    { "Value": 0.24, "Tags": { "load": "load15" } }
  ]
}

If the process fails (non-zero exit, timeout), Wigo reports status 500 for that probe. Exit code 12 disables the probe until restart; 13 disables and removes its result.

---

Building from source

Prerequisites

• Go and GCC
• Node.js and npm (for the frontend)
• GOPATH set in your environment

Install dependencies

make deps

Build

make clean release

Build for all supported architectures (amd64 & armhf)

Requires arm-linux-gnueabihf-gcc:

make clean releases

Build Debian packages

Requires dpkg-deb:

make debs

Development mode

Run Wigo with hot-reload for backend and frontend:

make run-dev

The web UI is at http://localhost:4400/ (or the port in etc/wigo-dev.conf). Stop with Ctrl+C.

Note: Development mode needs sudo. Artifacts are stored in dev/.

---

Usage

Web interface

Web interface requires the HTTP API to be enabled locally in [Http] (see Configuration).

By default the web interface is at: http://[your-ip]:4000/

CLI

CLI requires the HTTP API to be enabled locally in [Http] (see Configuration).

/usr/local/wigo/bin/wigocli

Example output:

Wigo v0.51.5 running on backbone.root.gg
Local Status    : 100
Global Status   : 250

Remote Wigos :

    1.2.3.4:4000 ( ns2 ) - Wigo v0.51.5:
        apt-security              : 100  No security packages availables
        hardware_disks            : 250  Highest occupation percentage is 93% in partition /dev/md0
        hardware_load_average     : 100  0.09 0.04 0.05
        ...

• Local Status — worst status among probes on this host.
• Global Status — same as local here; for the whole view, check each remote’s status in the list.